Welcome to visit the official website of Shandong Sudiao Intelligent Equipment Co., Ltd.

 中文 | Admin  |  Home

The Practitioner of automation application solutions in the woodworking industry

Customized Production, Super Quality, Worry-Free Service

Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.

News Center

Contact Information

Business Department:

Sales Manager: Juan Liu

Tel : +86-531-88271994

Mob:+86-13305314695

E-mail:sales@sudiao.com

E-mail:juan@sudiao.com 

WhatsApp&weChat:

Juan: 0086-13305314695

Welcome to your consultation and corporation.

Contact us if you're interested in our products or you need technical support.

 

Three Major Causes of Tool Wear in CNC Cutting Machines and How to Identify Them—Worth Saving!


Release Date:

2026-06-28 12:15

   CNC cutting machine Tool wear is a concern for many users. Like many machine components, wear on the cutting tools of a panel saw is inevitable; however, by identifying its causes and implementing protective measures, we can minimize wear and ensure more efficient maintenance of production equipment. Let’s examine the primary causes of tool wear in panel saws and how to assess them.

 CNC cutting machine

  During the material‑cutting process, the rake face and flank face of the cutting tool frequently come into contact with the chip and workpiece, generating intense friction, high temperatures, and significant pressure; consequently, these surfaces are prone to wear. Wear can be classified into the following categories:

  1. When the cutting edge is worn during machining, the chip comes into contact with the rake face, resulting primarily in crescent-shaped concave wear.

  2. When cutting brittle materials with the back rake face, the contact length between the cutter and the back rake face is relatively short, and the comparatively blunt cutting edge leads to significant wear on the back rake face.

  3. When cutting steel with edge wear, deep grooves are often ground on the side of the primary cutting edge near the workpiece surface and on the side of the secondary cutting edge near the tool tip.

  Severe tool wear can be assessed from the following aspects:

  1. When the cutting machine is operating normally, the cutting tool emits a shrill, piercing noise.

  2. Listen to the spindle; it will produce noticeable abnormal noises.

  3. During the cutting process, the cutting machine exhibits noticeable vibration, and the machine tool spindle also vibrates significantly.

  4. After the cutting machine completes the material cutting, the die on the bottom surface may exhibit variations in quality.

  Tool wear stage of the cutting machine:

  In general, tool wear can be divided into three stages: initial wear, normal wear, and rapid wear.

  Initial wear stage: The primary cause of tool wear during woodworking machining is that the cutting temperature remains too low, failing to reach the optimal cutting temperature. At this stage, wear is predominantly abrasive, exerting significant adverse effects on the tool and increasing the likelihood of chipping or breakage. This phase is highly critical; if not properly managed, it can directly lead to catastrophic tool failure.

  When using cutting‑off equipment, tools are prone to chipping during the initial wear stage. To prevent such failure, proper break‑in is essential, allowing the cutting edge to gradually reach an optimal operating temperature. Experiments show that after break‑in, tool life can increase by approximately twofold.

  The break-in procedure involves halving the feed rate while maintaining an appropriate spindle speed, with a machining time of approximately 5 to 10 minutes. Use the lower value when machining soft materials and the higher value when machining hard metals.

  During the initial wear stage, the cutting temperature of the tool reaches a certain level, giving rise to primary wear and diffusive wear, which primarily cause localized flaking. Consequently, wear is relatively minor and progresses slowly.

  When wear reaches a certain threshold, the cutting tool becomes ineffective and enters a phase of rapid wear. At this point, the phenomena described above occur, and the tool must be replaced.

 CNC cutting machine

   CNC cutting machine Tool wear primarily encompasses the scenarios outlined above. While natural wear is unavoidable, proper operating procedures can help minimize it. Monitoring the wear condition of cutting‑machine tools and identifying the specific type of wear—so as to determine whether replacement is necessary—is a critical skill that cutting‑machine operators must master.

Keywords:

CNC cutting machine