Welcome to visit the official website of Shandong Sudiao Intelligent Equipment Co., Ltd.

 中文 | Admin  |  Home

The Practitioner of automation application solutions in the woodworking industry

Customized Production, Super Quality, Worry-Free Service

Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.

News Center

Contact Information

Business Department:

Sales Manager: Juan Liu

Tel : +86-531-88271994

Mob:+86-13305314695

E-mail:sales@sudiao.com

E-mail:juan@sudiao.com 

WhatsApp&weChat:

Juan: 0086-13305314695

Welcome to your consultation and corporation.

Contact us if you're interested in our products or you need technical support.

 

Don’t panic if your panel saw encounters any of the following malfunctions—our woodworking panel saw manufacturer is here to help!


Release Date:

2026-06-28 12:15

   Woodworking panel cutting machine manufacturer Please note that during operation, panel saws inevitably encounter malfunctions of varying degrees—this is perfectly normal. In fact, many issues can be resolved independently, provided you have the skills to diagnose and troubleshoot them. With that in mind, let’s take a look at how panel saw manufacturers address four common types of faults. We hope this information proves helpful!

  1. The cutting machine has triggered an overtravel alarm, indicating that the machine has reached its maximum travel limit during operation. Please follow the steps below to perform a check:

  1. Does the design’s dimensions exceed the processing limits?

  2. Check whether the connection cable between the machine’s motor shaft and the leadscrew is loose. If it is, tighten the screw.

  3. Are the machine and computer properly grounded?

  4. Whether the current coordinate value exceeds the soft limit range.

  5. When the cutting machine triggers an overtravel alarm and subsequently clears it, all motion axes automatically switch to jog mode. As long as the manual direction key remains pressed, once the machine moves away from the limit position—i.e., disengages from the overtravel limit switch—the connected motion state can be restored at any time. When moving the worktable, be sure to orient the movement away from the limit position.

  II. Non-Alarm Faults of the Cutting Machine

  1. If the repeat machining accuracy is insufficient, refer to item 2 under section 1 for inspection.

  2. When the computer is running but the machine remains stationary, check whether the connector between the computer control card and the electrical cabinet is loose. If it is, reinsert it and tighten the securing screws.

  3. When the machine returns to its mechanical home position, no signal is detected. Perform the check as described in the previous item: the proximity switch for the mechanical home position is faulty.

  III. Output Fault of the Cutting Machine

  1. No output—please check that the connection between the computer and the control box is secure.

  2. Open the manager’s settings, check whether the storage is full, and delete any unused files in the manager.

  3. Check whether the signal cables are loose, and carefully verify that each cable is properly connected.

  IV. Cutting Machine Malfunction During Material Cutting

  1. Check whether the screws in each component are loose.

  2. Verify that the path you are working with is correct.

  3. Regardless of whether the file is too large, the computer should handle errors.

  4. Adjust the spindle speed up or down to suit different materials (typically 8,000–24,000 rpm). Note: For stepless‑speed spindles, the idle speed range may be 6,000–24,000 rpm. Select an appropriate speed based on material hardness, machining quality requirements, feed rate, and other factors. Generally, use higher speeds for harder materials, smaller feeds, and fine finishing. In most cases, avoid setting the speed excessively high to prevent motor overload.

  5. Loosen the tool holder, reorient the cutter and clamp it securely, then align the tool properly to ensure a smooth finish on the engraved surface.

  6. Inspect the cutting tool for damage; replace it with a new one and resume material cutting.

  The aforementioned malfunctions of the woodworking panel‑cutting machine can be diagnosed through observation and inspection; therefore, there is no need to panic when these issues arise. Woodworking panel cutting machine manufacturer Please note that following the provided instructions will resolve the issue effectively. If you encounter any problems that cannot be solved, or if you experience any difficulties during use, feel free to contact us at any time—our expert technicians will provide you with detailed guidance.

Keywords:

Woodworking panel cutting machine manufacturer