Welcome to visit the official website of Shandong Sudiao Intelligent Equipment Co., Ltd.

 中文 | Admin  |  Home

The Practitioner of automation application solutions in the woodworking industry

Customized Production, Super Quality, Worry-Free Service

Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.

News Center

Contact Information

Business Department:

Sales Manager: Juan Liu

Tel : +86-531-88271994

Mob:+86-13305314695

E-mail:sales@sudiao.com

E-mail:juan@sudiao.com 

WhatsApp&weChat:

Juan: 0086-13305314695

Welcome to your consultation and corporation.

Contact us if you're interested in our products or you need technical support.

 

Does your long‑used CNC cutting machine need recalibration? Come on in—let us walk you through it step by step!


Release Date:

2026-06-28 12:10

   CNC cutting machine With prolonged use, the machine’s data may inevitably accumulate some deviations. For experienced panel‑cutting‑machine operators, it is then necessary to perform adjustments to ensure the machine’s accuracy. Next, SUDU CNC will walk you through how to calibrate a panel‑cutting‑machine that has been in service for an extended period.

 CNC cutting machine

  How to adjust a long‑used panel saw and ensure the following points:

   I. Grinding and Repair of the Cutting Machine Conveyor Belt

  First, start the cutting machine; the worktable can be raised to engage with the abrasive belt. During a single pass, the material removal should not exceed 0.1 mm to prevent thermal deformation of the belt. After adjustment, remove any worn debris and set the thickness gauge to zero.

   II. Dressing and Grinding of the Thickness-Setting Roll

  Adjust the worktable to ensure it is level. After removing the abrasive belt, place a template made of 60–80 grit sandpaper on the conveyor belt surface, raise the worktable so that the sandpaper lightly contacts the roller, and move the template back and forth along the length of the rebar. Once adjusted, remove the chip and reset the zero point.

   III. Adjustment of the Pressure Roller

  Raise the sanding pad, remove the abrasive belt, and lift the worktable. Gently touch the conveyor belt with the thickness‑setting roller, then adjust the worktable according to the thickness reading until the pressure roller lightly contacts the conveyor belt; finally, tighten the nut.

   IV. Abrasive Belt Oscillation Adjustment

  It is controlled by a photoelectric switch; adjusting its position allows you to change the swing reference point of the abrasive belt. Typically, the protective fiber of the abrasive belt is positioned about 1 cm from the rod’s edge and is monitored by two pairs of photocells. When the reference point aligns with the rod’s edge, the system stops at that position.

   V. Sand Cushion Leveling

  Raise the sanding pad, remove the abrasive belt, place the spirit level on the conveyor belt, and lift the worktable until the thickness‑adjustment roller lightly contacts the level. Then move the spirit level from one end of the sanding pad to the other to check its levelness; if any deviation is detected, adjust it by turning the left‑ and right‑hand threaded screws on the sanding pad.

   6. Display Zeroing

  The CNC cutting machine is pre‑zeroed before leaving the factory. After adjusting the table’s flatness and polishing the conveyor belt and the thickness‑setting rollers, the thickness display must be reset to zero.

 CNC cutting machine

   CNC cutting machine Its introduction has enhanced both the production efficiency and processing quality of panel furniture; however, as a CNC machine, it is inevitable that errors will accumulate over prolonged operation. Therefore, it is essential to recalibrate long‑used panel‑sawing machines. We hope the above guidance helps you perform proper adjustments on your panel saw!

Keywords:

CNC cutting machine