Welcome to visit the official website of Shandong Sudiao Intelligent Equipment Co., Ltd.

 中文 | Admin  |  Home

The Practitioner of automation application solutions in the woodworking industry

Customized Production, Super Quality, Worry-Free Service

Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.
Shandong Suku Intelligent Equipment Co., Ltd.

News Center

Contact Information

Business Department:

Sales Manager: Juan Liu

Tel : +86-531-88271994

Mob:+86-13305314695

E-mail:sales@sudiao.com

E-mail:juan@sudiao.com 

WhatsApp&weChat:

Juan: 0086-13305314695

Welcome to your consultation and corporation.

Contact us if you're interested in our products or you need technical support.

 

Experience Sharing: How to Properly Use and Maintain the Water-Cooled Vacuum Pump for Woodworking Panel Saws?


Release Date:

2026-06-28 12:15

  Now, Woodworking panel saw Its widespread application has become a market trend. It is worth noting that a panel‑cutting machine is, in fact, composed of numerous components; however, during operation, malfunctions in these parts are inevitable. The following sections outline the operating requirements and key precautions for the water‑cooled vacuum pump used in panel‑cutting machines, with the aim of helping users better maintain their equipment and enhance production efficiency.

 Woodworking panel saw

  The suction force of the cutting machine has already been discussed. In fact, this suction force is closely linked to the water‑cooled vacuum pump. Many manufacturers equip their machines with vacuum pumps tailored to customer requirements, yet they fail to communicate the necessary precautions, leading to numerous issues during subsequent operation.

  Currently, water-cooled vacuum pumps on the market typically come in power ratings of 4.0 kW, 5.5 kW, and 7.5 kW. The vacuum suction force varies with the pump’s power.

  1. Each time the vacuum pump is started, ensure that it contains working fluid, and that the fluid level is above the motor shaft.

  2. The water‑circulation vacuum pump must be equipped with a vacuum hood to prevent contaminants from entering the pump.

  3. Equipped with a check valve to prevent water from flowing back into the equipment when the motor is stopped.

  4. Fill the water tank until water begins to flow from the upper outlet, and replenish the tank at regular intervals each day to ensure it remains adequately filled for operation.

  5. Before starting, ensure that all valves are fully open, and fill the pump with water prior to activating the vacuum pump.

  6. The vent hole must not be blocked; air should be drawn in through the vent to create a vacuum. Do not connect piping longer than 2 m with a diameter of less than 5 cm, as this may cause the motor to overload and become damaged.

  7. The suction inlet and exhaust port of the cutting machine must be tightly sealed to prevent air leakage.

  8. Start the motor to prevent jamming (this step is not necessary, as the factory will verify this; generally, there are no major issues).

  9. Install an overload protector for the motor to prevent it from burning out due to overload.

  10. Open the priming valve on the pump and wait for a few minutes to ensure that the working fluid has fully filled the pump.

  11. Start the motor and the vacuum pump, then test the adsorption strength.

  12. After the equipment has been running for approximately 10 days, drain the water from the vacuum pump and replace it with clean water to prevent impurities from entering the pump, which could reduce its adsorption capacity, and to effectively inhibit rusting of the water tank.

  13. After using the vacuum pump, clean the water tank, inlet pipe, and replace the water within 150 days. If the pump will not be used for a short period, close the water‑tank inlet valve and drain the water from the inlet pipe. If the pump will remain idle for an extended period, drain and properly store the water in the tubing and pump head to prevent rusting and ensure proper operation.

 Woodworking panel saw

  In addition, the water-cooled vacuum pump is not directly mounted on Woodworking panel saw Additionally, please carry it with you when shipping; the technician will install it upon arrival for training. Otherwise, the machine may incur significantly higher shipping costs. We would also like to emphasize that, in the event of a malfunction, be sure to contact the manufacturer promptly to avoid unauthorized repairs, which could lead to unnecessary expenses.

Keywords:

Woodworking panel saw